Read this manual carefully and have your installer instruct you on your system’s operation and on which features have been implemented in your system. I have a DSC model alarm () and this installer code was . The Down and Dirty at unlocking a DSC Alarm with Installers. Parent Directory · PC Pager · PC Partition · PC v Demo User · PC v Installation · PC
|Published (Last):||11 May 2014|
|PDF File Size:||19.55 Mb|
|ePub File Size:||8.31 Mb|
|Price:||Free* [*Free Regsitration Required]|
Okay, I took the keypad for the graj door opener apart last night. If I want to lock the door out, I kill power to the whole unit.
Short answer, shorting the two wires together will raise or lower the graj door -easy. The programming for PGM2 is described in the installation manual, which you can download from this website – see the Online Manuals tab above. I’m probably over-thinking this being an engineering type.
Since I dont have the “installer code” I can’t get into it and want to know how to reset the system?? What is this button cluster? I guess there’s some value in the lock dc5010. Tub pump air tube came off.
They must be putting an AC signal on the two wires and sensing the impedance at that AC frequency.
How to reset a DSC PC-5010 V2.0, installer code?
To confuse matters further there are 4 contacts on the opener itself which are shared between the cluster, photocell and beam. BB code is On. Not sure why they didn’t just use resistors though. Hopefully I’ve made this clear enough, I’m sure this has been done a hundred times.
SMF – Just Installed! It’s a long way down to that concrete instlalation your roof trusses are at 12 feet. You could use one of the commonly available relays for security work. There must be a circuit breaker that will disconnect power for that ladder job.
Re: DSC PC – how to change Install and Maint codes?
My installer of course will not give me the “installer code” which I need. Greetings, I’m new to this alarm stuff but very conversant on a technical level. A family member could have come along and installwtion the door while I was up on a ladder in the door travel area thinking the opener was disabled by the lock function. It does not lock out the wireless keypad mounted on the exterior door frame. The same breaker might shut the lights off in the garage, also – that would be a challenge.
I think I still might do that even though I also have a lock button. Anyway, just thought I’d share with others whom may have a Chamberlain installztion door opener. Didn’t realize you could invert the logic level. October 08, That said, the “alleged” lock button not locking out the wireless keypad is a major design flaw. If anyone know this please email me or reply.
Posted In Plumbing and Piping. Trying to hook up tire changer motor to switch. You may not post new threads. The output I’m planning on having drive a small relay. Did you miss your activation email? Programming suggestions welcome here. There’s also an LED backlight. LandLine Gold Member Posts: I’ll power down the thing and pull the cluster apart.
How to install and programme DSC to open and shut my garage door
The main button will be zero ohms, and the other two will be higher values. There are two wires that go to my Chamberlain Liftmaster garage door opener control.
I have all the answers. Real Knowledge From Real People. My opener has two buttons, one opens the door and the light installayion on automatically and the other turns on the light without opening the door. Step 5 – When Zone Light 1 is lit on the keypad the default is complete. Step 4 – Apply AC power to the main panel.
Please login or register. I’ve yet to see one wired in this manner in a residence. If nothing else, I now know how to make my own full-function keypad. Find all posts by MrRonFL. I believe 1uF and 50uF. The default procedure is on page The logic in the motor control will cycle through down-stop-up with each press. I no longer use the lock function. The house I bought had a DSC alarm system all wired in.