All rights reserved. Printed in the Netherlands. All product names are trademarks of their respective companies. Fluke // ScopeMeter. Users Manual. Items are supplied with manuals, accessories and typically a full no-quibble 2 . 2 Fluke Corporation ScopeMeter C/B Series, Series and the NEW. Path: /fluke/B/. This is the These manuals are available for download and free of charge. Fluke B/B-C/B-C ScopeMeter Service Manual.
|Genre:||Health and Food|
|Published (Last):||5 June 2018|
|PDF File Size:||2.25 Mb|
|ePub File Size:||3.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
Comments to this Manuals Your Name. Use caution when using 1: Page 7 Contents continued Triggering on Video Signals All narrow positive pulses shorter than 5 ms are now displayed on the screen.
FLUKE B USER MANUAL Pdf Download.
Printed in the Netherlands. The display also shows the actual waveform. Electronic Connections for Scope spring to voltages higher than 30 Vrms from earth ground.
A Select Probe Cal with the arrow message indicates when the DC calibration has completed keys, then accept. It performs an FFT to transform the amplitude waveform from the time domain into the frequency domain. From scope mode, open the menu. Fluke series ii scopemeter family product datasheet 10 pages. When your test tool is in manual range, do the following: This function can be used to monitor waveforms like motion control signals or the power-on event of an Uninterruptable Power Supply UPS.
After a reset, the test tool is dc-coupled so that ac and dc voltages appear on the screen. To replay continuously, do the following: Meter mode has the advantage of high measurement resolution. Page 97 For other countries, a line plug adapter complying with the applicable National Requirements must be used.
The introduction gives examples to show how to use the menus and perform basic operations. This the input A and input B waveform, the test tool will display function smoothes the displayed waveform. Connect the short ground leads of each voltage probe to its own reference potential. Triggering on Missing Pulses See next This chapter provides an introduction to the trigger section. ZOOM To zoom in on a waveform, do the following: Correct connection of reference leads Figure Note that the Freezing the Screen Peak-Peak reading for input B appears next to the input A You can freeze the screen all readings and waveforms at frequency reading at the top of the screen.
For example, to following: Tips Using the Tilt Stand Using the Tilt Stand Resetting the Test Tool The test tool is equipped with a tilt stand, allowing viewing If you want to reset the test tool to the factory settings, do from an angle while placed on a table.
Typically, NiMH batteries always meet the specified Display the key labels. Enter text from picture: For complete service, not use abrasives, solvents, or alcohol. During recording samples are continuously saved in deep memory. Page 71 Triggering on Waveforms Triggering on Pulses Finding Missing Pulses Select the positive pulse icon to trigger on the gap between the The next example covers finding missing pulses in a train positive pulses, then jump to of positive pulses.
Initially, you have 2 divisions of pre-trigger view negative delay.
Switching Glitch Detect to Off will suppress the high frequency noise on a waveform. This averages Capture the outcomes of 64 acquisitions. Also See for B Service manual – 86 pages Security procedures – 2 pages. Fluke t and t electrical tester datasheet 2 pages.
Fluke 192B User Manual
Got it, continue to print. Select the desired trigger slope, and jump to Level: Note To maximally benefit from having independently Figure 6.
Set the vertical amplitude scale to linear or logarithmic. Triggering on Manuaal Triggering on Pulses Finding Missing Pulses Select the positive pulse icon to trigger on the gap between the The next example covers finding missing pulses in a train positive pulses, then jump to of positive pulses.
When fully charged, the batteries provide 4 hours of use. DC to 20 kHz As soon To reduce jitter on the screen when triggering on noisy as the test tool receives a trigger, the waveform is waveforms, you can use a noise rejection filter. Fluke’s warranty obligation is limited, at Fluke’s option, to refund of the purchase price, free of charge repair, or replacement of a defective product which is returned to a Fluke authorized service center within the acopemeter period. Read First Warning To avoid electrical shock or fire: If the signal changes, the setup is automatically adjusted to maintain the best display result.
The following tables list the user-replaceable parts for the Display the key labels. The horizontal frequency scale is always logarithmic. Chapter 7 Tips About this Chapter Using the Standard Svopemeter This chapter gives you information and tips on how you The following illustrations show the use of the standard can make the best use of the test tool. Initially the power shutdown time is 30 minutes.
Look at the top of the test tool. The Spectrum function shows the spectral content of the input A or input B waveform.
However, if replacement is needed, this should be done by qualified personnel only. Averaging will suppress Display the key labels.